Home

How to Seal Entry Points to Keep Pests Out

To seal entry points and keep pests out, inspect your home's exterior, repair damaged screens and covers, and close gaps with materials pests can't easily chew through or dislodge. Choose a repair that suits each opening, keep ventilation and drainage routes clear, and check for animals inside before sealing their access points.

Where to look for pest entry points

Start at ground level and work your way around the building. Use a torch and inspection mirror to check hidden edges, and photograph any damage so you can find it again when you're ready to make repairs.

  • Check where pipes, cables and air-conditioning lines pass through exterior walls.
  • Inspect door bottoms, garage-door corners, window frames and damaged insect screens.
  • Look along foundations, wall joints, cladding edges and gaps behind exterior fittings.
  • Check accessible roof edges, soffits, vents and chimney covers from a safe position.
  • Inspect beneath sinks, behind appliances and around service pipes inside cupboards.

Look for droppings, gnaw marks, greasy rub marks, nesting material and insects repeatedly entering the same crack. These clues help you identify openings pests are using. Don't disturb droppings or nesting material during your inspection.

Prioritise gaps of about 6 mm or larger for mice, but don't stop there. Small insects can enter much narrower cracks, and seemingly narrow gaps may widen behind loose trim. Ask a qualified contractor to inspect damage at roof level rather than climbing onto an unsafe surface.

Which materials keep pests out?

Choose materials that bond securely to the surrounding surface and withstand movement, moisture and chewing. A neat bead of sealant won't close a deep opening effectively if pests can push through the material behind it.

  • Exterior-grade sealant: Use a product rated for the surface and expected joint movement to close narrow cracks around fixed frames and openings for pipes or cables.
  • Metal mesh and flashing: Use securely fixed, corrosion-resistant mesh or sheet metal for larger openings rodents can reach. To keep mice out, choose mesh with openings no larger than about 6 mm.
  • Mortar or suitable masonry repair compound: Remove loose material, then repair holes in otherwise sound brickwork, blockwork and concrete.
  • Weatherstripping and door sweeps: Fit these to moving doors and windows where a rigid filler would prevent normal operation.
  • Purpose-made pest-resistant covers: Choose correctly sized covers for suitable vents and service openings without reducing the airflow they need.

Don't rely on expanding foam alone where rodents can reach it. They can gnaw through it, and exposed foam may deteriorate. You can use foam to fill concealed voids where appropriate, but protect accessible openings with a securely fastened, chew-resistant barrier.

How to seal gaps around pipes and cables

First, identify what passes through the opening. You'll need different materials and methods for a water pipe, electrical cable, flue or opening in a fire-rated wall. Never inject ordinary foam into electrical equipment or pack combustible material around hot pipes or flues.

Remove loose filler, dirt and failing sealant without damaging the pipe or cable. Let the surface dry, then follow the sealant manufacturer's instructions for surface preparation, gap size and curing. For deep joints, use suitable backing material to support the sealant and help it form the correct shape.

For a larger hole rodents can reach, fit corrosion-resistant metal mesh or a shaped metal plate around the pipe or cable and fasten it to sound material. Close any remaining small gaps with a compatible sealant. Don't compress cables, obstruct valves or cover connections that need inspection.

Seal accessible indoor gaps as well as the exterior opening, particularly beneath sinks and behind kitchen units. Don't dismantle appliances or disturb gas, electrical or refrigerant connections. Ask a qualified tradesperson to seal openings that need specialist work.

How to seal gaps around doors and windows

Close each exterior door and check the sides, top and threshold for visible light. Fit weatherstripping where the door meets its frame, and install a sweep or threshold seal that makes continuous contact without preventing the door from closing properly.

Check the corners carefully. A sweep can touch the threshold across most of its width while leaving an opening beside the frame. Repair damaged thresholds and correct door alignment rather than adding layers of soft material that quickly wear away.

For windows, replace torn insect screens and repair loose frames. Seal fixed joints between the frame and surrounding wall, but leave moving tracks and built-in drainage channels clear. The U.S. Department of Energy recommends caulking for stationary gaps and weatherstripping for components that move.

Which openings should you leave unsealed?

Don't seal intentional openings simply because they lead outdoors. Air bricks, wall weep holes, roof vents and appliance outlets may provide essential ventilation, drainage or a safe route for exhaust gases.

Where appropriate, fit a purpose-made guard that keeps the target pest out without stopping the opening from working properly. Fine insect mesh can restrict airflow, and unsuitable covers can collect debris. Check the building or appliance requirements before choosing a screen.

Never cover a combustion-air inlet or flue with improvised mesh. Take particular care with dryer outlets because screens can collect lint. If pests can enter through the existing outlet, ask a qualified contractor to choose a compatible pest-resistant replacement.

How to check for pests before sealing entry points

If you hear scratching, find fresh droppings or see animals using an opening, check for animals inside before permanently closing it. You could trap animals, separate adults from dependent young or force pests into living areas if you seal an occupied space.

For rodents, combine sealing entry points with an appropriate monitoring and control plan rather than assuming repairs will remove an existing infestation. The U.S. Environmental Protection Agency recommends prevention measures that remove pest access to food, water and shelter. Seek professional help for infestations you can't reach, bats, nesting birds or other wildlife that may need specialist removal or legal permission to remove.

After repairs, inspect each seal once it has cured and check that doors, windows and vents still work correctly. Recheck repaired areas regularly and investigate fresh droppings, gnaw marks or repeated insect activity. Replace loose mesh, split sealant and worn door seals promptly rather than filling over a failed repair.

Sources